SMART TESTING>> Guaranteed quality also in small production runs

Thanks to its experience in a multitude of sectors, Mechatronics Labs has created an extremely effective instrument for testing the customer's product, even on small production runs, for any application and type of electronics, testing software included: SMART TESTING.

SMART TESTING is done on functional test benches "custom made" to test the customer's product. They are made with with very reasonable investment costs. This is made possible by the modularity of the hardware and software.

The fully stand-alone instrument with its back-panel and SUB-D connectors, can interface with any mechanical fixture of test bench or mechanical system, bed-of-nails, and other testers. In collaboration with selected partners, Mechatronics Labs designs and also provides the mechanical part of the test bench (fixture) or system studied ad hoc to meet the customer's requirements.

The SMART TESTING test bench can also be interfaced with a PC

The instrument also uses predictive maintenance technology: the software monitors the status of the instrument and mechanical parts to notify you if it requires maintenance or calibration in good time. This preventing possible problems and unnecessary costs caused by malfunctions or faults on the test bench.

Many different tests can be performed on the basis of how the instrument is configured.

Below you'll find just a few examples: 

  • Target power test, checks current absorption, power inversion test if necessary. Monitors current absorbed and checks for shorts. If a short circuit or anomaly is found, the system interrupts the power supplied to any loads and the target.
  • Programming microcontrollers or FPGA on target.
  • Generating stimuli of all kinds, from physical stimuli in specific points to a command line parser on a target microcontroller, also to check any microcontroller peripherals.
  • Measuring the response on the basis of the sequence, from physical measurements taken in specific points to monitor checks using a command line parser, also to check any microcontroller peripherals.
  • Measuring load current using internal current probes
  • Tests on power loads using closed loops. Measure and compare closed loop response curves.
  • Measure and check wave form. Measure and compare the frequency, amplitude, and duty-cycle of a specific signal.
  • Etc.

Mechatronics Labs' engineering services can also design the electronics of the product to be tested, on the basis of the testing to be done. This saves hours in terms of development time needed to design the bench, with a further reduction in terms of cost and time. 

For more information, download the Entry Level Datasheet file.

DATASHEET_ENTRY LEVEL_v1.0_preliminary_EN.pdf

This base structure can be implemented with the following extensions:

 

NEWS - Mechatronics

Products

  • IO-Link Slave Module en +

    IO-Link Skave Module>> IO-Link Slave Module is the embedded solution to quickly integrate the IO-Link interface, without hoursof additional development.  IO-Link Slave Module key features are: A Single component for bilateral transfer of data Integration of the communication Io-Link Stack, IO-Link physical transceiver and Microcontroller. Does not need of additional developments firmware for the management… Read More
  • IDENTITY +

    IDENTITY>> Your product in the Internet of Things Thanks to its multidisciplinearità, Mechatronics Labs has created IDENTITY, the product of the future accessible to small producers and craftsmen with short time to market. IDENTITY is a basic product that can transform the customer's product in a digital identity. The base, easily adaptable and customizable on… Read More
  • SMART TESTING +

    SMART TESTING>> Guaranteed quality also in small production runs Thanks to its experience in a multitude of sectors, Mechatronics Labs has created an extremely effective instrument for testing the customer's product, even on small production runs, for any application and type of electronics, testing software included: SMART TESTING. SMART TESTING is done on functional test benches "custom made"… Read More
  • 1

See also

 
SERVICES


Design

Prototyping

Management of production process

Procurement

Consulting

Temporary Management


COMPETENCES

 

X-Engineering - Mechatronics

X-Mecha - Servo drive

X-Bus - Communication

X-FPGA - High Performance

X-Sensor - Sensors

X-Mobile - Smart connection

PRODUCTS


IO-Link Slave Module

Smart testing - Test benches

Identity - Internet of Things

 

 

 

CONTACT US

Via Ornago, 24

20883 Bellusco (MB) - Italy

Tel.: +39 039 6020240 

Fax: +39 039 6200955

@: info @mechatronicslabs.it